烟气脱硫脱硝
Your current location : Home >> News >> Technical news

ContactContact Us

Shenyang Yuneng Mechanical Engineering Technology

Contact person for drying and calcining technology: Yu Zongchun (teacher)

Tel: 13904039686

Contact person of environmental protection and energy conservation technology: Jiang Baoyi (teacher)

Tel: 18102429424

Marketing Department Contact: Yu Lei (Manager)

Tel: 13080705497

Address: No. 8-19, Fumin South Street, Hunnan New District, Shenyang

Liaoning Kiln Desulfurization and Denitration Factory Talks about Corrosion Resistant Raw Materials of Desulfurization and Denitration Equipment

2022-09-16 15:00:00
a

Liaoning Kiln Desulfurization and Denitration Factory Talks about Corrosion Resistant Raw Materials of Desulfurization and Denitration Equipment

Desulfurization and denitration equipment has a good corrosion resistant raw material. Epoxy resin (phenolic plastic, epoxy resin adhesive and polyurethane resin) is used to solidify them into a whole. The compressive strength of the material can be comparable to that of construction steel - hence its name is fiberglass anti-corrosion. You should understand a little since the strength of this product is very high.

Desulfurization of Liaoning kiln

The desulfurization and denitrification equipment has a good corrosion-resistant raw material FRP is a good corrosion-resistant raw material, which has good resistance to air, water, acids, alkalis, salts of general concentration, as well as a variety of feed oils and solutions. However, its defect is also very obvious, that is, its long-term and heat-resistant layer is very poor. Generally, FRP cannot be used for a long time under high temperature. The compressive strength of general-purpose polyester FRP decreases significantly when it is above 50 ℃, and it is generally not used below 100 ℃. The compressive strength of general-purpose epoxy resin FRP decreases significantly when it is about 60 ℃.

Liaoning kiln desulfurization and denitration manufacturer: Advantages of industrial kiln desulfurization and denitration equipment

1. Desulfurization and denitrification equipment: cheap and easy to assemble. The water can be recycled, and the actual effect of flue gas desulfurization can be achieved by adding weakly alkaline water into the reservoir.

2. The service life of the centrifugal fan can be extended when the desulfurization and denitrification equipment is installed behind the fan.

3. The internal structure of the desulfurization and denitrification equipment can withstand washing, corrosion, heat resistance, and is solid and durable.

Liaoning kiln desulfurization and denitration manufacturer: operation and maintenance of desulfurization and denitration equipment

1. Before operation, the fan shall be turned on first, and then the water supply equipment shall be powered on. When blowing the boiler pipe, the power supply to the system software shall be suspended before turning off the fan.

During operation, the cylinder section must not be shut down. Regularly maintain whether the overflow chute is smooth. At the same time, frequently observe the flue gas temperature and the flue dust friction resistance.

2. Clean the dust in the grit chamber on time and try to keep the cleanliness of the cooling circulating water.

Liaoning kiln desulfurization and denitration manufacturer: measures to avoid freezing and cleaning of desulfurization and denitration equipment

Although it has entered spring, it is still very cold in North China. Desulfurization and denitrification equipment will still be frozen and cleaned. Let's share how to prevent freezing and cleaning of machinery and equipment.

1. In winter, power plants and boiler manufacturers work intensively. Desulfurization and denitrification equipment are always working uninterruptedly. Long term operation of machinery and equipment will cause common failures and stop operation. During shutdown and maintenance, it is necessary to ensure that the slurry pipeline of desulfurization and denitrification equipment is in the state of heating. The liquid supply and wastewater pipelines should be flushed. The flange plate at the connection of the pipeline should be disassembled and disassembled for the lower part of the pipeline to discharge liquid, After maintenance, check whether there is freezing in the pipeline, and flush the pipeline for the second time.

2. If the soot superheater fails, the air circuit to the machine and equipment must be suspended, and the stored water shall be discharged from the equipment as soon as possible to avoid freezing and cleaning.

3. In case of power failure during the operation of desulfurization and denitrification equipment, the power supply system of machinery and equipment shall be restored as soon as possible to ensure the normal operation of transmission equipment, pipelines and their electric heat tracing system software. If the power supply system cannot be restored for a long time, the water storage areas in the equipment will be drained.

Liaoning Kiln Desulfurization and Denitration Manufacturer: Well, we won't give too much explanation today. Thank you for watching. If you need desulfurization and denitration equipment, please consult our factory.

Website of this article:http://en.syyntec.com/news/537.html

Shenyang Yuneng Mechanical Engineering Technology Co., Ltd

Contact person for drying and calcining technology: Yu Zongchun (teacher)

Tel: 13904039686

Contact person of environmental protection and energy conservation technology: Jiang Baoyi (teacher)

Tel: 18102429424

Marketing Department Contact: Yu Lei (Manager)

Tel: 13080705497

Address: No. 8-19, Fumin South Street, Hunnan New District, Shenyang

Copyright 2021 Shenyang Yuneng Mechanical Engineering Technology All rights reserved. Liao ICP No. 2021010103-1